Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Frisco, TX
Gate access control in Frisco usually means one of two things: a keypad that stopped accepting codes, or a phone-entry system that won’t release the gate when a delivery driver calls. Most of the homes we work on across Frisco were built between 2000 and 2015, which means the original access hardware is now hitting the end of its serviceable life all at once. If your gate won’t open from the keypad or the intercom has gone silent, call (817) 826-9477 and we’ll walk through what you’re seeing before we dispatch anyone.
Why Frisco Homes Are Different
Frisco’s housing stock is unusually consistent for a city this size. The master-planned buildout from roughly 2000 to 2015 put up tens of thousands of brick and stone homes across Stonebriar, Starwood, Phillips Creek Ranch, and Richwoods, and most of them included ornamental iron driveway gates as standard or upgraded features. Those gates are now aging together, which is why we see the same failure patterns repeat across entire subdivisions.
The bigger factor is the soil. Frisco sits on Blackland Prairie clay that expands when wet and contracts when dry. That movement tips gate posts out of plumb, and a post leaned two or three inches off vertical will tear through an operator in a season or two. We check post plumb on every call in Frisco before we touch a single wire, because fixing the operator without fixing the post just means another callback in six months. The February 2021 freeze also did real damage here: cracked hydraulic lines and seized gearboxes across the city in a single week. HOAs govern nearly every replacement part, so anything visible from the street usually needs architectural approval before we install it.
Our Main Frisco Services
Two services account for most of the calls we run in Frisco: access-control failures and parts-and-welding repairs. The three pages below cover the larger repair, installation, and motor work that Frisco homeowners ask about most.
Gate Repair in Frisco
When a gate binds, grinds, or stops halfway, it’s usually a post that has moved, a hinge that has worn, or an operator fighting against both. We handle the full repair path in Frisco: diagnose the mechanical issue, correct any post or hinge problem first, then repair or replace the operator. Powder-coated iron gates from the 2000s buildout respond well to repair, and our preference is always to fix what’s there rather than sell a replacement that may not clear HOA review. Gate Repair in Frisco
Gate Installation in Frisco
New gate work in Frisco means navigating two layers: the physical reality of expansive clay soil and the administrative reality of HOA design standards. We measure, check underground utilities, pour or set posts to a depth that resists seasonal heave, and install a gate that matches the street profile your HOA has on file. If a specific iron style or setback is required, we document it in the written scope before any concrete is poured. Gate Installation in Frisco
Gate Motor & Opener in Frisco
Frisco’s tract-built homes often came with entry-level swing operators that are now failing in clusters. We replace or service motors from LiftMaster, FAAC, BFT, DoorKing, Elite, and others, matching the new operator to the gate’s weight and travel rather than swapping in whatever is on the truck. If the post has shifted, we correct that first; an operator installed on a leaning post is a warranty claim waiting to happen. Gate Motor & Opener in Frisco
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Frisco
Gate access control in Frisco covers the systems that decide who gets through: keypads, remote receivers, phone-entry boxes, card readers, and video intercoms. Homes built during the 2000-2015 master-planned wave across Frisco typically had one of a few entry-level access systems installed at the builder’s cost point, which means we now replace or repair keypads and telephone-entry boards across Stonebriar, Starwood, and Phillips Creek Ranch on a regular basis. Clay-soil freeze-thaw cycles fill keypad housings with condensation that corrodes circuit boards, and the February 2021 storm killed a generation of outdoor keypads that were never sealed for that kind of cold. Our Gate Access Control work always includes a photo record of the wiring before and after, so the next technician doesn’t have to guess what changed.
Keypad Entry
Signs you need it
A keypad that takes multiple presses to register, lights up but doesn’t release the gate, or has a screen that fades in direct Texas sun.
What it costs in Frisco
A replacement keypad installed in Frisco typically runs $225-$525 depending on whether it’s a simple coded unit or part of a networked system.
How we do it
We open the housing, photograph the existing wiring, verify voltage, replace the unit, reprogram codes, and seal the housing against moisture.
Phone Entry
Signs you need it
Visitors report the call rings but the gate won’t open, or the dial tone never connects at all.
What it costs in Frisco
Phone-entry repairs in Frisco typically land between $250 and $600, replacing the control board, wiring the relay, or swapping the whole unit.
How we do it
We test the phone line at the gate, check relay output, replace the failed board or unit, and leave a photo log of the new wiring.
What Gate Access Control Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Keypad replacement | $225-$525 |
| Phone-entry board repair | $250-$600 |
| Video intercom install | $550-$1,500 |
How much does a new keypad cost in Frisco?
A new gate keypad in Frisco runs $225-$525 installed, depending on the model and whether we’re replacing a standalone unit or integrating with an existing phone-entry system. Call (817) 826-9477 for a written price after we see your existing wiring.
Can you add phone entry to an existing Frisco gate?
Yes. If the operator has an accessory port, we can add phone entry for $250-$600 in most Frisco installations. We’ll confirm compatibility during the estimate and put the full price in writing before starting.
Gate Parts & Welding in Frisco
Gate parts and welding in Frisco means fixing the iron itself, not just the motor. When a post tips two to four inches off vertical, the gate binds, the operator grinds, and the hinges take load they were never designed to carry. Our Gate Parts & Welding service addresses the mechanical foundation before any electronic part gets touched.
Hinge Replacement
Signs you need it
The gate sags toward the latch side, scrapes the ground, or the hinge pins show visible wear and ovaled holes.
What it costs in Frisco
Hinge replacement in Frisco typically runs $130-$400 per hinge depending on gate weight and whether welding is required.
How we do it
We support the gate, remove the worn hinge, weld or bolt the replacement to the post and stile, and photograph the new hardware.
Post Replacement
Signs you need it
The post leans visibly, the gate no longer meets the latch, or the operator fights to close against ground contact.
What it costs in Frisco
Post replacement in Frisco runs $400-$950 per post, including concrete removal, new footing, and resetting the gate plumb.
How we do it
We dig out the old footing, set a new post in concrete below the frost line, rehang the gate, and verify plumb before the operator is re-engaged.
What Gate Parts & Welding Costs in Frisco
| Item | Typical range in Frisco |
|---|---|
| Hinge replacement | $130-$400 per hinge |
| Post replacement | $400-$950 per post |
| Custom welding repair | $150-$600 per section |
Does the clay soil in Frisco really break gates?
Yes. Frisco’s expansive clay shifts gate posts seasonally, which throws gates out of alignment and destroys operators. We check post plumb on every call and fix the post before replacing any motor. Call (817) 826-9477 for an inspection.
Can you weld a broken ornamental iron gate in Frisco?
We can. Custom welding in Frisco runs $150-$600 per section depending on the break, the finish matching, and whether the piece must be removed for bench work. We photograph every weld before and after.
Brands We Service in Frisco
Our Frisco trucks carry parts and control boards for DoorKing, Elite, Mighty Mule, and LiftMaster, along with generic receivers and safety edges that work across common swing and slide operators. See our brands for the full list. Most board swaps and hinge replacements finish same day; custom-ordered parts usually arrive within three to five business days.
Pricing for Gate Repair in Frisco, TX
| Service | Typical range in Frisco |
|---|---|
| Keypad replacement | $225-$525 |
| Phone-entry board repair | $250-$600 |
| Video intercom install | $550-$1,500 |
| Hinge replacement | $130-$400 per hinge |
| Post replacement | $400-$950 per post |
| Custom welding repair | $150-$600 per section |
| Gate motor replacement | $450-$1,200 |
| Roller and rail repair | $200-$600 |
Prices in Frisco push toward the higher end when HOA approval delays parts, when post work is needed before an operator can be installed, or when a gate must be removed for bench welding. Every job gets a written price before any work starts, and that number doesn’t change unless you approve the change first.
Neighborhoods We Serve in Frisco
We work throughout Frisco, from Stonebriar and Starwood to Phillips Creek Ranch, Richwoods, and the older streets near the Rail District. Response time is typically under two hours for gate-outs and security failures.
- Stonebriar
- Starwood
- Phillips Creek Ranch
- Richwoods
- The Rail District
Service Area - Cities Near Frisco
Alongside our work in Frisco, we serve adjacent communities in the northern metro. The same black-clay soil patterns appear in Prosper, TX and Little Elm, TX, and we run regular routes through Denton, TX and Lewisville, TX. Dispatch for all of these is coordinated from our Dallas-Fort Worth area office.
Serving Frisco, TX - Our Local Coverage Area
We’re based in the Frisco area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Frisco
We usually reach Frisco addresses within two hours for a gate stuck open or closed. A live person answers (817) 826-9477 around the clock, so you’ll speak to a technician who can ask the right questions before we dispatch. Emergency response applies to security failures, not scheduled installations.
For like-for-like repairs, usually not. If a decorative finial, a visible post cap, or a different gate style is required, many Frisco HOAs want architectural review first. We can document the existing design with photos so your submission matches what the committee expects. The written price doesn’t change while you wait for approval.
Most of the ornamental iron in Frisco is powder-coated flat-top or spear-top in standard black, brown, or bronze. We match the existing finish on welding and replacement parts, and we photograph the color match before the piece leaves our shop. If the HOA requires a specific RAL code, we’ll confirm it with you before powder-coating.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Frisco Customers Say
"Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H.