Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Carrollton
New gate installation in Carrollton averages $4,800-$18,500, depending on whether it’s a single swing gate off a 1980s driveway or a double slide gate at a Valley Ranch HOA entry. Most jobs take one to three days once HOA approval and parts are locked in. We handle the approval paperwork, the concrete work, the operator wiring, and the final safety check so you don’t have to chase down a management company mid-project. Call (817) 826-9477 for a written quote before anything gets ordered.
A gate installation in Carrollton is never just “hang a frame and go.” Half the work happens before a single post hole is dug. The homeowner signs the contract, but the HOA signs off on the style, height, finish, and operator type. Then the soil underneath does its damage if the footing isn’t deep enough. We confront both realities on every job. That’s why we price in writing, document what we find, and leave a photo record when we’re done. The clay under this city doesn’t care about your covenants, and the covenants don’t care about your timeline. We coordinate both.
Why Vance Gate Repair Lewisville Is Carrollton’s Preferred Gate Installation Company
Carrollton gets a specific mix of gate work. The neighborhoods along the Sam Rayburn Tollway and Dallas Parkway were built between 1975 and 1995, which means a large stock of original ornamental iron driveway gates are now corroding at post collars and weld joints. At the same time, the black clay soil along the Elm Fork corridor torques posts out of plumb after every hard rain followed by a dry spell. We see these two failure modes every week, from New Koreatown commercial roll-downs to Valley Ranch HOA entry systems.
Since 2014, Adrian Vance has built this company around one habit: write down what you found, what it costs, and what you left behind. That’s the Haven Standard. Clause 1 is a written price before work starts. Clause 4 is photographic evidence on every visit. It means a Carrollton homeowner who got a gate installed in 2021 can show a future technician exactly what was set, what brand was used, and where the limit switch landed. No guesswork. No paying twice.
When you call Vance about a new gate in Carrollton, a live person answers. At 2 a.m. on a Tuesday, it’s still a person. That matters when a swing gate has sheared an arm bracket and is hanging half-open across a driveway in Indian Creek. We’re not voicemail. We’re not a callback queue. That’s the standard, and it applies to quotes, scheduling, and emergency calls alike.
Our Gate Installation Services in Carrollton
Driveway Gate Installation
Most Carrollton driveway gates we install are ornamental iron or aluminum swing sets on concrete footings. The critical variable is the post depth, and we size footings for the clay, not for the gate’s weight alone. A standard single driveway swing gate in Carrollton runs $3,200-$7,800 installed, including hinges, latch, and concrete work. Double gates run higher because the leaf geometry and the center latch point put more stress on both posts. We hand you the written price before the first auger goes in the ground.
Pedestrian Gate Installation
Pedestrian gates in Carrollton tend to fail along the latch line, where the catch bolt and the post strike plate take daily abuse. A new pedestrian gate with a Maglock or keypad entry runs $1,400-$3,300. If the gate is part of a perimeter fence, we check the adjacent fence posts too, because a sagging line post can telegraphed a misalignment into the gate gap within a season. The Elm Fork neighborhood soil does not forgive a shallow pedestrian post.
Sliding Gate Installation
A slide gate is the right answer for many 1980s Carrollton driveways where the garage sits close to the lot line and a swing leaf would smack the Sam Rayburn Tollway feeder curb. Sliding gate installation in Carrollton typically runs $6,500-$15,000, and the steel V-track or cantilever carrier system is the part most companies underbid. We spec the track for 20 years of thermal expansion in the Texas sun, because a warped track is a seized gate by August. We install Gate Installation systems with the operator, safety loops, and post hardware as one coordinated unit, not as an afterthought.
Swing Gate Installation
Swing gates dominate Carrollton’s 1990s subdivisions, and that era’s geometry is predictable: two leaves, a center latch, and a motor post that gets yanked sideways by the clay every dry season. Swing gate installation here runs $3,800-$11,000, and we always bring a laser level to check the post plumb before hanging leaves. A gate that’s been through a few North Texas drought cycles is rarely square on the first measurement. We also handle double swing gates extensively, because most HOA entries in Valley Ranch were built as double gates, and the refooting process is the same.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Carrollton
Vance installs and services nine major gate-automation brands, so what’s already in your Carrollton home or community determines your best path. LiftMaster slide operators are what we spec for most Valley Ranch HOA entries because the rack and pinion system holds up on longer slide spans. Elite is common on older Carrollton swing gates, and its current SL3000 line is a direct swap for many original units. DoorKing shows up in commercial roll-downs and older gated communities. We don’t steer you toward replacement when repair is the right move, but when a new install is warranted, we match the operator to the gate’s cycle rate, not to a vendor rep’s quota.
Common Gate Installation Problems We See in Carrollton Homes
- HOA rejection of gate style or finish. Carrollton subdivisions around the Dallas North Tollway hold very specific covenants, right down to the acceptable ornamental iron picket spacing and powder-coat color. We pull the architectural guidelines before we write the quote, so you don’t install a gate that gets red-tagged two days later.
- Clay soil heave on new posts. The shrink-swell clay along the Elm Fork corridor can lift a shallow post out of plumb within a year. We dig deeper than the generic spec and use a concrete collar design that holds the post through both the wet and dry extremes of a North Texas year.
- Operator conflicts with existing keypad entry. We install a new slide or swing operator without coordinating with the management company’s shared entry system, and suddenly the community keypad no longer activates the new motor. We pull the wiring diagram and the access-control panel before we touch a control board, so integration is part of the bid, not an extra charge after the fact.
- Corroded weld points on 1980s iron gates. The original ornamental iron gates on Carrollton’s 1980s tract homes are now forty years old, and the welds at the post collars are the first thing to fail. We check the frame with a tap test before recommending repair or full replacement, and we’ll show you the corrosion in the photos before you sign.
Pricing for Gate Installation in Carrollton, TX
Here’s where we put the number in front of you. A basic single swing driveway gate with a standard operator in Carrollton runs $4,800-$7,800. A double gate with an HOA-compliant ornamental iron frame runs $7,000-$15,000. A slide gate on a V-track or cantilever system runs $6,500-$15,000. A pedestrian gate with Maglock or keypad runs $1,400-$3,300. All of these include the concrete footing, the operator wiring, the safety photo-eyes, and the UL 325 entrapment check, but not the HOA application fee. The written price you sign is the price you pay. If a footing gets deeper or a control board needs an extra relay, we note the change and get your signature before we do the work. No surprise invoices. That’s Clause 1 of The Haven Standard.
We Also Serve Cities Near Carrollton
Vance Gate Repair handles gate installation across the northern metro: Coppell, Lewisville, Plano, and Grapevine all fall within our regular service loop. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and crews routinely run Carrollton appointments the same day as a Lewisville or Coppell callout. If you’re in one of those cities, the same written-price standard applies.
Serving Carrollton, TX - Our Local Coverage Area
We’re based in the Carrollton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Carrollton
Yes, in almost every Carrollton subdivision built before 2000, you need architectural review before a new driveway gate is installed. The covenants in planned communities along the Dallas North Tollway and Sam Rayburn Tollway corridors mandate specific ornamental iron or aluminum styles, heights, and finishes, and a board that doesn’t see the application until after the concrete is poured will make you tear it out. We pull the guidelines, draft the submission package, and include the approval wait in the project timeline. Call (817) 826-9477, and we’ll tell you the exact approval requirement for your neighborhood.
Post footings in Carrollton need to go 36 to 48 inches deep at minimum, and we spec a deeper concrete collar wherever the Elm Fork’s wet-dry cycling has already heaved nearby fence lines. The goal is to anchor below the shrink-swell zone, because a post sitting in the active clay layer will rotate out of plumb within the first year. We photograph the hole before the concrete goes in, so you see exactly what was done in the record.
Yes, we coordinate the operator with your management company’s shared entry system, including keypad controllers, loop detectors, and any LiftMaster or DoorKing access panel already in place. We don’t treat the gate motor as a standalone box; we wire it as a node in the existing system, and we leave the relay and wiring diagram on file for the next technician. If the management company needs our notes before sign-off, we hand them over directly.
Yes. UL 325 requires entrapment protection on every automatic gate installation, and that means photo-eyes, a reversing edge, or both, plus a stop sensor on the motor. We set and test these on every install, log the settings, and leave the compliance record with you. No gate leaves our truck without passing the entrapment check. It’s the same commercial-grade habit Adrian Vance established in 2014, applied to every Carrollton driveway.
A slide gate is usually the right call when the driveway is short and the feeder road is close, because a swing leaf needs room to arc across the property line without hanging over the sidewalk. We’ve installed dozens of slide gates along the Tollway-adjacent streets of Carrollton, and the V-track or cantilever design eliminates the swing arc entirely. Swing gates still work when the driveway has a deep setback, but for those tight lots near the Tollway, we’ll spec the slide and the operator to match.
Written by Adrian Vance, Owner at Vance Gate Repair, serving Carrollton since 2014.