Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Hurst
A new driveway gate in Hurst typically runs between $2,400 and $8,500 installed, depending on the gate material, operator brand, and whether we’re replacing posts that have heaved out of plumb. Most swing gates in this city’s older ranch-style neighborhoods need the post work done before we can hang a new gate properly. Call (817) 826-9477 and we’ll walk the site, probe the soil, and hand you a written price before any tool comes off the truck.
We work in Hurst every week. We know the clay. We know where the original 1960s post footings are shallow enough to fail. And we know that a gate installed correctly here needs a concrete footing driven below the active clay layer, not just a bag of Quikrete in a hole. That’s the difference between a gate that still latches in ten years and one that drags the ground by spring.
Why the Blackland Prairie Clay in Hurst Decides Whether Your Gate Lasts
Here’s what we see in Hurst that we don’t see in most newer suburbs. The residential core of this city sits on Blackland Prairie clay, and that soil expands and contracts with every wet-dry cycle. In neighborhoods like Hurst Hills and Bellaire, decades of that movement have pushed original wooden gate posts three to five inches out of plumb. The gate that used to swing clean and latch now drags the driveway or misses the strike plate entirely.
That’s not a hinge problem. It’s a footing problem. And it’s the reason our Gate Installation team probes soil depth before quoting any swing gate work in Hurst. If the post is walking, the real fix is a new concrete-footed post set below the active clay layer. We’ve pulled old posts out of Hurst yards where the concrete was barely 18 inches deep, sitting entirely inside the shrink-swell zone. A Hurst gate post needs more than that. We go deeper.
This is the defining gate installation challenge in Gate Installation in Hurst: the hardware is rarely the root cause of failure. The soil is. Every quote we write for this city accounts for it.
Why Vance Gate Repair Lewisville Is Hurst’s Preferred Gate Installation Company
Adrian Vance started this company in 2014 doing commercial access-control work, where every job required a written scope, a written price, and a documented record of what was done. We brought that same habit to residential gates. Every gate we install in Hurst gets the same treatment: a written price before we start, and a photo log of every adjustment and part number before we leave.
Our crews are in Hurst on a regular schedule. We know the ranch layouts off Precinct Line Road, the long driveways north of Pipeline Road, and the 76053 and 76054 zip codes where the original cedar posts are now 40 to 60 years old. We service nine automation brands, including Viking, Ghost Controls, and DoorKing, so we’re not going to steer you toward replacing a motor when a repair is the honest answer.
Every installation carries our 365-Day Done Right Promise. If something isn’t right within a year, we make it right. No argument, no fee, no expiration date inside that window.
BeforeAfterOur Gate Installation Services in Hurst
Driveway Gate
A driveway gate in Hurst does more than mark the property line. It controls access to a long entry, often on a lot where the house sits well back from the street. We install steel and aluminum driveway gates sized to your opening, whether that’s a standard 12-foot residential swing or a wider double configuration. The post work is the critical part here. On Hurst clay, we drive the footing below the active layer and set the post plumb with the gate hung before the concrete cures, so nothing shifts.
Swing Gate
Swing gates are the most common style on Hurst ranch homes, and the most likely to fail from post heave. We recommend steel posts and a continuous concrete footing deep enough to outlast the shrink-swell cycles. If you’re replacing an old wooden swing gate on a property in the older subdivisions, expect us to talk about the post before we talk about the gate panel. A new gate on a walking post is a temporary fix.
Sliding Gate
On Hurst properties with shorter setbacks or driveways that slope toward the street, a sliding gate often works better than a swing. The track and roller assembly has to handle a specific condition here: the ground moves. We set the track on a concrete base that spans the travel path, and we check the roller alignment against clay heave over the first full year. A sliding gate on Hurst clay that’s properly based won’t bind when the soil expands in spring rain.
Pedestrian Gate
We also build and install pedestrian gates alongside driveway gates or as standalone entries. These are usually lighter than driveway gates, but the post requirements are the same on Hurst soil. A pedestrian gate post that heaves even two inches will throw the latch out of alignment. We set them the same way we set the big ones: deep, concreted, and below the active clay layer.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
What Hurst Heat and Freeze Cycles Do to Gate Hardware
Hurst sits squarely in the Dallas-Fort Worth heat corridor. Summer days routinely push past 100°F, and that heat expands metal gate hardware: hinges, latches, operator arms. The February 2021 freeze cracked aged wood gate frames across the city and seized automatic gate motors that were never rated for prolonged sub-freezing temperatures.
When we install a gate in Hurst, we account for both extremes. We use sealed bearings and powder-coated hardware that won’t bind when the swing gets tight in August, and we spec operators with metal gears and proper entrapment protection for cold-weather operation. A box-store operator bought off the shelf often lacks the safety photocells and force limits that matter most during a summer power surge or a winter ice event.
Trusted Brands We Service in Hurst
We work on whatever motor is already on your property. We service and install Viking, Ghost Controls, DoorKing, and Elite operators, along with LiftMaster, FAAC, BFT, Linear, and Mighty Mule. For Hurst customers, that means we can match a new operator to your existing gate frame rather than forcing a full replacement. We keep common parts for these brands stocked on our trucks, so a service call in Hurst usually gets finished same visit, not two weeks later waiting on a bracket.
Common Gate Installation Problems We See in Hurst Homes
- Heaved hinge posts. The Blackland Prairie clay under Hurst expands in spring rains and contracts in summer drought. Over decades, this walks a post three to five inches out of plumb. The gate drags or won’t latch. The fix is a new footing below the active clay layer, not a hinge adjustment.
- Warped wooden gate frames. Original cedar and pine gate frames from the 1960s through 1980s have endured repeated 100°F heat and ice storms. They’re warped, rotted at the base, and no longer square. New hardware mounted to a warped frame just transfers the problem.
- Undersized operators with no entrapment protection. We see a fair number of Hurst driveways with swing or slide operators purchased from retail chains. They lack proper force limits and photocells, which is a genuine safety issue when a summer storm throws a power surge through the board.
- Double gates sagging in the middle. A double driveway gate in Hurst sags when the center posts or the frame wasn’t engineered for the clay movement. One side settles faster than the other, and the gates no longer meet at the latch. We address this with a welded undergate support or a deeper center footing.
What We Did on a Precinct Line Road Driveway
We installed a solar-powered sliding gate operator on a long rural driveway off Precinct Line Road, where running mains power to the gate would have meant trenching several hundred feet through clay and landscaping. Our crew drove a new concrete post footing below the active clay layer to stabilize the hinge post, then mounted a LiftMaster operator with a Viking loop detector and safety photocells. The loop detector opens the gate for vehicles leaving the property without anyone touching a keypad. The photocells stop the gate if something crosses the path. The whole job was documented, photographed, and the price was written before we started.
That’s the standard we apply to every gate installation in Hurst. The Haven Standard. Written scope, written price, and a photo record before we leave. Clause 4: Evidence on every job.
Pricing for Gate Installation in Hurst, TX
A basic steel swing gate with manual operation in Hurst starts around $2,400 to $3,800, including posts set below the clay line. Adding an automatic operator brings the range to roughly $4,200 to $6,500, depending on the brand and whether you need a loop detector, keypad, or safety photocells. A sliding gate installation runs $3,500 to $6,000 for the gate and track, plus $1,500 to $2,800 for an operator if you want automation. Double driveway gates typically land between $5,500 and $8,500 installed, with the post work being the biggest variable on Hurst clay.
Every quote is written and handed to you before we start. No verbal estimate, no surprise invoice. If the soil probe shows we need a deeper footing than the original quote assumed, we talk to you about that before the concrete gets poured, and the adjusted price is in writing. You can request a free second opinion on any written estimate from another company. Bring the paperwork. We’ll review it at no cost.
We Also Serve Cities Near Hurst
Our crews cover North Richland Hills, Bedford, Colleyville, and Euless, so if you’re just over the city line, we can still get to you. The soil conditions change a bit across the metro, but the same rules apply: written pricing, documented work, and a gate that stays square. Call (817) 826-9477 and tell us where you are.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Hurst
Because the concrete wasn’t deep enough. If the footing sits inside the top 18 to 24 inches of Hurst’s Blackland Prairie clay, the expanding soil grips it and pushes it up with every wet season. The fix is a new footing driven below the active clay layer, typically 36 to 48 inches, with a wider base. Call (817) 826-9477 and we’ll tell you what your current post looks like before we quote the repair.
You can, but we don’t recommend it. Most retail operators lack proper entrapment protection, which is a genuine safety concern on a gate that a child or pet could wander into the path of. They also tend to have plastic gearboxes that fail faster in Hurst’s heat. A proper operator from Viking, Ghost Controls, or LiftMaster with force limits and safety photocells costs more up front and lasts years longer. We’ll quote you a written price either way and explain the differences before you decide.
A keypad works fine for entry. The loop detector is what opens the gate automatically when a vehicle pulls up from inside, so you don’t have to punch in a code every time you leave. Most Hurst homeowners want both: a keypad for guests and delivery drivers, and a loop detector buried in the driveway for daily use. We can install both and wire them into the operator on the same visit.
Solar is the answer for most long-driveway properties in Hurst, especially off Precinct Line Road and the rural stretches east of the city core. A solar panel charges a battery bank that runs the operator, and the system is sized for the operator’s draw. You don’t need mains power at the gate. We spec a panel and battery combination that holds up through North Texas summers and cold snaps. The power requirements get written into the quote, and the installation is documented with photos.
The center posts are settling at different rates because of the clay. One side of the driveway may be in soil that gets more water than the other, so it expands and contracts differently. The result is a gap or overlap at the latch. We fix it by adding a welded undergate support or resetting the center posts below the active clay layer. Either way, the price is written before we start. Call (817) 826-9477 for a site visit and a quote.
Get a Written Price for Your Hurst Gate Installation
Tell us what you’re looking for and where you are in Hurst. We’ll schedule a site walk, probe the soil, and hand you a written price with the scope spelled out. No verbal-only estimates, no surprise invoice at the end. If you already have a written estimate from another company, bring it. We’ll review it at no charge and give you our honest read. Call (817) 826-9477 today. A live person answers.
Written by Adrian Vance, Owner at Vance Gate Repair Lewisville, serving Hurst, TX.