Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Hurst
Gate repair in Hurst usually comes down to one of three problems: a post that’s heaved out of plumb in the clay, a gate frame that’s warped or rotted after 40 to 60 years of North Texas weather, or an automatic operator that’s either obsolete or binding in the heat. Most repairs run $180 to $480, and a post re-set with a new concrete footing typically lands between $350 and $700 depending on how deep we have to go. We work in Hurst every week, know the soil and the housing stock, and we’ll give you a written price before any tool comes off the truck. Call (817) 826-9477 and a live person answers, day or night.
This page is written for Hurst homeowners specifically. If you’re on a 1960s ranch lot in Hurst Hills or Bellaire, or off Precinct Line Road near the older subdivisions, what’s failing on your gate is probably different from what fails on new construction in Colleyville or Southlake. That difference matters when you’re deciding between a hinge adjustment and a post re-set, and we explain it in plain terms below.
Why Vance Gate Repair Lewisville Is Hurst’s Preferred Gate Repair Company
We built our reputation in Hurst on a simple habit: we show you what we found, in writing, with photos, before we ask you to pay for the fix. Adrian Vance started doing commercial access-control work in 2014, and the documentation discipline from that trade, wiring diagrams, part numbers, limit-switch readings, came with us into every residential gate we touch. In Hurst, that means when we reset a post or replace an operator, you get a photographed record of the old footing, the new concrete collar, the part number installed, and the limit settings we programmed. No gate company in this area does that consistently on residential work.
The 365-Day Done Right Promise applies to every repair we complete in Hurst. If the work isn’t right within a full year, we come back and make it right at no charge. No argument, no fee, no expiration date inside that window. We also hand you a written price before any work starts, which is Haven Standard Clause 1, and we don’t consider that a selling point so much as the bare minimum of honest contracting. Every technician dispatched to Hurst is background-checked, uniformed, and you’ll get a name and photo before arrival.
Dispatch and scheduling for Hurst are coordinated from our Dallas-Fort Worth office, and our crews serve Hurst locally with same-day response on most repair calls. We don’t route you through a call center or a voicemail loop. A live person picks up the phone 24 hours a day, seven days a week.
Our Gate Repair Services in Hurst
Here’s what we actually do in Hurst, week after week. Each of these is shaped by what we see in this city’s specific housing stock and soil, not generic gate work.
Electric Gate Repair
Electric gate repair in Hurst usually means one of two things: a control board that’s gone obsolete, or a motor that’s binding because 100-degree heat cycles have warped the drive components. Many Hurst homes still run the original operator from the 1980s or 1990s, and a lot of those units predate UL 325 safety requirements, meaning they never had proper photo-eye sensors or edge detection. We service nine automation brands, LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so we work on whatever motor is already on your property rather than steering you toward a replacement just because it’s easier for us.
Automatic Gate Repair
Automatic gate repair in Hurst often involves retrofitting safety sensors onto legacy operators. The pre-UL 325 units we see in the older neighborhoods east of Precinct Line Road typically lack a working photo-eye, the infrared beam that stops the gate if something crosses the path, or a functioning edge sensor. Retrofitting is possible on some boards and not on others; we’ll tell you straight which is cheaper before you spend a dollar. If the board is unrepairable, the honest answer is usually replacement, and we’ll document the exact reason in writing so you’re not guessing later.
Hinge & Post Repair
This is the defining gate repair in Hurst. The original cedar and pine posts set in the 1960s through 1980s sit in expansive Blackland Prairie clay that shrinks and swells with every wet-dry cycle. Over decades, that movement walks posts three to five inches out of vertical, which makes the gate drag, bind, or fail to latch. A hinge adjustment alone won’t fix that. The real fix is cutting the old footing, setting a new pressure-treated post below the active clay layer with a concrete collar, and re-hanging the gate so it swings true. We do this work constantly in Hurst Hills, Bellaire, and the older subdivisions throughout the city.
Gate Realignment
Gate realignment in Hurst is usually the follow-up to a post problem. Once a post has heaved, the gate throws the hinges out of alignment, the latch stops engaging, and if it’s an automatic gate, the operator’s limits are now off by several degrees, which strains the motor and shortens its life. We reset the post, re-hang the gate, and then recalibrate the operator so the travel limits match the gate’s actual swing. We photograph the new limit positions and leave that record with you.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Hurst
We stock common parts for the brands Hurst homeowners actually have, and we service all nine major gate-automation lines. If your gate runs on Viking, Ghost Controls, DoorKing, or Elite, we have the diagnostic tools and the programming experience to work on it same day, and we don’t need to order parts from a distributor and make you wait a week. We also keep control boards, photo-eyes, and edge sensors for the older LiftMaster and FAAC units that are still common in Hurst’s ranch-era subdivisions. The point is this: we repair what’s there. We don’t sell you a new operator because we don’t recognize the old one.
Common Gate Repair Problems We See in Hurst Homes
These are the failures we document most often on Hurst service calls, and each one is a direct product of this city’s soil, climate, or housing age. If your gate is acting up, it’s likely one of these four.
- Post heave from expansive clay: The original wooden posts set in the 1960s to 1980s sit in Blackland Prairie clay that shrinks in summer droughts and swells during spring rains. Over 40 to 60 years, that cycle walks posts up to five inches out of plumb, causing the gate to drag the ground or refuse to latch. New hinges won’t fix it; the post footing has to be re-set below the active clay layer.
- Rotted post bases and warped frames: Cedar and pine gate frames from Hurst’s original ranch subdivisions have weathered decades of 100-degree heat and several hard freezes, including the February 2021 ice storm that cracked aged wood throughout the region. Bases rot where water pools against the post, and the frame twists out of square. We see this most in Hurst Hills and the older neighborhoods east of Precinct Line Road.
- Legacy operators without modern safety sensors: Many automatic gates in Hurst still run the original operator, often a pre-UL 325 model with no working photocell or edge sensor. Boards on these units are frequently obsolete and unrepairable, and the safety gap means the gate won’t reverse if a child or pet crosses its path. We can retrofit sensors on some boards; on others, replacement is the cheaper and safer answer, and we’ll show you the numbers both ways.
- Heat-seized hinges and rack-and-pinion drive components: Hurst sits squarely in the DFW heat corridor, where summers routinely exceed 100°F. Metal hinges, latches, and rack-and-pinion drives expand and bind in that heat, then contract again in winter freezes, cracking aged wood frames and seizing motors that were never rated for prolonged sub-freezing temperatures. That’s a maintenance cycle that never lets up on a 50-year-old gate.
Pricing for Gate Repair in Hurst, TX
Here are honest numbers for Hurst’s market, written down the way we’d put them on a quote sheet.
- Hinge replacement (single gate): $140-$260, including new hinges and labor
- Post re-set with new concrete footing: $350-$700, depending on depth and whether the old footing has to be cut out
- Gate realignment and latch adjustment: $120-$240
- Photocell or edge sensor retrofit: $180-$380, if the existing board supports it
- Operator diagnosis and limit recalibration: $95-$180
- Control board replacement: $280-$650, depending on brand and model
The price we give you is the price on the invoice. We write it down before any work begins, under Haven Standard Clause 1, and we don’t add surprises at the end. If you have a written estimate from another company, bring it to us, and we’ll review it at no cost. Call (817) 826-9477 for an exact quote, it’s free and it’s in writing.
We Also Serve Cities Near Hurst
Our crews work throughout the mid-cities and surrounding suburbs. If you’re in North Richland Hills, Bedford, Colleyville, or Euless, you’re still in our regular service area, and the same written-price, documented-record standard applies. For a closer look at what we do across the region, see our Gate Repair team’s full service page. And if you’re a Hurst homeowner researching your options, start here: Gate Repair in Hurst.
Serving Hurst, TX - Our Local Coverage Area
We’re based in the Hurst area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Hurst
Your gate post is almost certainly heaving in the expansive Blackland Prairie clay that underlies Hurst. Spring rains swell the clay around the post footing, which pushes the post up and out of plumb, and by summer’s drought the post has walked far enough that the gate drags the ground and the latch misses its strike plate. The fix is a post re-set with a new concrete footing driven below the active clay layer, not another hinge adjustment. Call (817) 826-9477 and we’ll confirm it with a level and a soil probe before we quote anything.
Sometimes yes, sometimes no, and we’ll tell you which before you spend a dollar. Some 1980s and 1990s control boards have the input terminals to accept a photocell and an edge sensor; others don’t, and forcing a retrofit on a board that was never designed for it is unreliable and unsafe. If the board is unrepairable, replacement is usually the cheaper honest answer, and we’ll write down the part number and the reason so you’re not guessing. Bring us your operator’s model number or a photo of the board, and we’ll give you a straight answer on the spot at (817) 826-9477.
Put a level on the post. If it’s more than about an inch out of vertical, or if the gate drags on one side and the hinges look intact, the post has heaved, and new hinges won’t solve the problem. Our techs recently reset a 1970s cedar swing gate in Hurst Hills where the hinge post had walked four inches out of vertical after spring rains. We cut the old footing, drove a new pressure-treated post below the active clay layer with a concrete collar, re-hung the gate, and recalibrated the LiftMaster operator’s limits. The gate now swings clean and latches without dragging. If you’re in Hurst Hills or any of the older subdivisions, call (817) 826-9477 and we’ll check the post first, it’s the right diagnostic order.
In Hurst’s climate, a well-built cedar gate frame on a properly set post typically lasts 15 to 25 years before the heat cycles, freeze-thaw stress, and moisture do enough cumulative damage that replacement is cheaper than repeated repairs. Pine frames from the original 1960s and 1970s builds are usually past that point by now, and many are warped, rotted at the base, or cracked from the February 2021 freeze. If the frame is still square and dry, we’ll repair it. If it’s not, we’ll tell you that too, and we’ll give you a written price for replacement before any work starts. Call (817) 826-9477 and we’ll assess it honestly.
Yes, modern safety standards require automatic gate operators to have working entrapment protection, and that means a photo-eye, an edge sensor, or both, depending on the installation. The original pre-UL 325 operators installed on many Hurst gates were never built with these, and that’s a real safety gap, especially if children or pets use the driveway. We can retrofit sensors on many operators; on others, the board won’t support the inputs and replacement is the only compliant option. We’ll document the exact recommendation and the cost in writing. Call (817) 826-9477 for a free assessment, we’ll tell you what your gate needs and what it costs, in plain English, before any work begins.
Contact Vance Gate Repair Lewisville for Gate Repair in Hurst
If your gate is dragging, binding, or refusing to latch, call us at (817) 826-9477. A live person answers 24/7, and we’ll schedule a Hurst technician to look at it, usually same day. You’ll get a written price before any work starts, and a photographed record of everything we found, set, and installed before we leave. No voicemail loop, no callback queue, no invoice surprises. That’s how we’ve worked in Hurst since our first service call here, and it’s not changing.
Written by Adrian Vance, Owner at Vance Gate Repair Lewisville, serving Hurst and the surrounding mid-cities since 2014.
Gate Repair in Nearby Areas
