Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Bedford, TX
Gate access control in Bedford usually means one of two things: an older keypad or intercom that’s stopped reading codes, or a gate motor that ignores its remotes. We fix both, and we start by looking at what Bedford’s soil and weather have done to the gate itself before touching a single wire. If your gate won’t open or won’t stop opening, call (817) 826-9477 and a live person answers, day or night.
Why Bedford Homes Are Different
Bedford’s residential streets were built almost entirely between the mid-1970s and early 1990s, and they sit on North Texas Blackland Prairie clay. That clay swells hard after rain and shrinks in summer drought, heaving gate posts that were set in shallow footings 30 to 50 years ago. The result: a gate that was hung plumb in 1987 is now leaning half an inch out, binding against the latch post, and forcing the motor to fight the frame every cycle.
The housing stock matters too. Original cedar pedestrian gates from that era were hung on galvanized strap hinges lag-screwed directly into the cedar post face. After four decades of heat cycling and clay movement, those lag holes strip out. What looks like a sagging gate is often a post that needs sistering or new hinge locations bored in fresh wood. Homeowners in HOA neighborhoods like Stonegate, Shady Brook, and Bedford Meadows deal with ornamental iron driveway gates added in the 1990s and 2000s, and those bring their own issues: rust at weld points, failing limit switches, and photo-eyes knocked out of alignment by lawn equipment.
Summer heat past 105°F warps cedar frames and makes steel tracks expand enough to bind. February 2021 snap-cast hinges and collapsed weakened post footings under ice load. Spring hailstorms dent aluminum panels across the Mid-Cities corridor. None of this is unusual to us, but it means a Bedford gate repair rarely stops at the broken part.
Our Main Bedford Services
Bedford homeowners call us most often for the three services below. Each has its own dedicated page with full pricing and details.
Gate Repair in Bedford
Most repair calls in Bedford start with a gate that drags, won’t latch, or has pulled its hinge screws out of a rotted cedar post. We rebuild the post or sister a new one beside it, then rehang the gate square and photograph the final alignment. Full detail is on the Gate Repair in Bedford page.
Gate Installation in Bedford
New gates in Bedford need deeper footings than the originals ever had, because Blackland clay will move any post set too shallow. We pour below the frost line, set the post, and hang the gate with hardware sized for the weight. See Gate Installation in Bedford for scope and pricing.
Gate Motor & Opener in Bedford
When a motor hums but the gate doesn’t move, or the gate reverses mid-travel, the problem is usually a limit switch, a capacitor, or a control board that’s been cooked by Bedford summers. We service nine automation brands and repair before replacing. Pricing is on Gate Motor & Opener in Bedford.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Bedford
Gate access control in Bedford means keypads, remotes, phone entry, card readers, and video intercoms attached to gates that were installed 20 to 35 years ago. The control boards, keypad membranes, and wiring have been through 105°F summers, hail, and at least one ice event, and most failures trace back to heat or moisture at the connection points. We service the equipment that’s already on the property rather than steering you toward a full replacement. This is the same documentation habit Adrian Vance built in commercial access-control work starting in 2014, brought to residential gates under Gate Access Control.
Keypad Entry
Signs you need it
Codes work intermittently, or the keypad lights but the gate won’t move.
What it costs in Bedford
Keypad replacement in Bedford typically runs $195-$425 depending on whether the wiring is intact.
How we do it
We test voltage at the keypad, replace the unit or the damaged wire run, and reprogram all codes with the homeowner present.
Video Intercom
Signs you need it
The screen shows no image, or the call button rings once and drops.
What it costs in Bedford
Video intercom replacement runs $380-$850 in Bedford, depending on the system and whether the camera cable is reusable.
How we do it
We identify whether the camera, the indoor monitor, or the cable between them failed, then replace only the failed component and photograph the new setup.
What Gate Access Control Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Keypad replacement | $195 - $425 |
| Remote control replacement | $140 - $260 |
| Video intercom replacement | $380 - $850 |
Can you come out the same day for a keypad that stopped working in Bedford?
Yes. We dispatch from our Dallas-Fort Worth office to Bedford daily, and a live person answers the phone 24/7. Call (817) 826-9477 and we’ll give you a written price before any work begins.
Do I have to replace the whole system if one keypad fails?
No. We replace the failed component only. If the wiring is intact, a new keypad connects to the existing controller. You get a photo record of what was found and what was installed.
Gate Parts & Welding in Bedford
Gate parts and welding in Bedford are usually needed because the original hardware has outlived its design life. Cedar posts from the 1980s rot at ground level, cast hinges snap under ice load, and steel frames fatigue at weld points from decades of clay-driven movement. We repair what’s there rather than throwing the gate away. Gate Parts & Welding covers it all.
Hinge Replacement
Signs you need it
The gate drags on the latch side, or the hinge screws spin without tightening.
What it costs in Bedford
Hinge replacement in Bedford runs $140-$350 per gate, including new heavy-duty hinges.
How we do it
We bore fresh hinge locations in sound wood or plate the post with steel, then rehang and photograph the final alignment.
Post Replacement
Signs you need it
The post leans, wobbles when pushed, or has pulled away from the fence line.
What it costs in Bedford
Post replacement in Bedford runs $280-$650 per post, including concrete and disposal.
How we do it
We dig below the frost line, set the new post in concrete, and brace it until the pour cures.
What Gate Parts & Welding Costs in Bedford
| Item | Typical range in Bedford |
|---|---|
| Hinge replacement | $140 - $350 |
| Post replacement | $280 - $650 |
| Rail repair or welding | $210 - $480 |
Can you weld a broken iron gate frame in Bedford, or do I need a new gate?
Most broken frames can be welded. We grind the failed weld, re-weld with proper penetration, and paint the repair. Replacement is only necessary when the metal itself is rusted through.
How long does post replacement take before I can hang the gate again?
We set the post in concrete and brace it. The gate goes back on the same day, but the post needs 24 to 48 hours to fully cure before heavy use.
Brands We Service in Bedford
We work on DoorKing, Elite, Mighty Mule, and LiftMaster gate operators in Bedford, along with FAAC, BFT, Linear, Viking, and Ghost Controls. Common parts are stocked locally for same-week service. Our brands page lists every system we cover.
Pricing for Gate Repair in Bedford, TX
| Service | Typical range in Bedford |
|---|---|
| Keypad replacement | $195 - $425 |
| Remote control replacement | $140 - $260 |
| Video intercom replacement | $380 - $850 |
| Hinge replacement | $140 - $350 |
| Post replacement | $280 - $650 |
| Rail repair or welding | $210 - $480 |
| Gate roller replacement | $175 - $390 |
| Chain or belt replacement | $160 - $320 |
Bedford prices push toward the upper end when a leaning post has to be replaced or sistered before the gate hardware can be touched, which is common on Blackland clay. Whatever the job, you get a written price before any work starts, and that price does not change unless you approve a change in writing.
Neighborhoods We Serve in Bedford
We cover all of Bedford, including the older cul-de-sac subdivisions where cedar gates and original posts are now 35 to 50 years old. Typical response time is same-day for repair calls.
- Stonegate
- Shady Brook
- Bedford Meadows
- Woodland Hills
- Harwood Terrace
Service Area - Cities Near Bedford
We also serve the surrounding Mid-Cities communities with the same written-price policy and photo-documented work. Nearby coverage includes Colleyville, TX, Euless, TX, Hurst, TX, and North Richland Hills, TX.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Bedford
Same day for repair calls. Our dispatch office is in the Dallas-Fort Worth area, and crews serve Bedford daily. Call (817) 826-9477 and a live person answers 24/7 with a scheduled arrival time.
Many Bedford HOA neighborhoods require approval for gate replacement or exterior changes, but repairs to existing hardware typically don’t. We provide a written scope and photo record that satisfies most HOA documentation requests.
We’ll give you a written price range over the phone, then confirm the exact flat price in writing before any work begins. No surprise invoices, no verbal estimates. It’s Clause 1 of our Haven Standard.
For gate repair in Bedford, call (817) 826-9477 for a free estimate with the price in writing before any tool is picked up.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Bedford Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.