Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Access Control Installation: The Lewisville Owner’s Guide
FAAC access control installation in Lewisville typically runs $450 to $1,400 installed, depending on whether you need a keypad, card reader, or full keypad-and-receiver pairing, and most jobs are completed same-day when the part is in stock. We keep FAAC-compatible keypads, receivers, and antenna kits on our trucks, and we match the part to your existing board revision before any wiring is touched. Most Lewisville owners discover the problem when the keypad stops lighting up, the remote works only from ten feet away, or the gate ignores every code entered after a storm.
Here’s the common thread: FAAC boards are picky about voltage and input type, and the access control side is almost never the motor. It’s the reader, the receiver, or the wiring between them. Our job is to confirm which one before you spend money on a part you don’t need.
Key Takeaways
- Installed FAAC access control work in Lewisville runs $450 to $1,400, written before we start
- We match the part to your FAAC board revision, not just the model number
- Same-day install is common when the part is on our truck
- Every visit includes a written scope, a written price, and a photo record of what changed
Which FAAC Models This Applies To
The most common FAAC gate operators in Lewisville are the 400, 402, 412, 415, 422, 750, 770, and the slide-gate 844 and C720 lines. The access control components we install for these break down into three groups: RP receivers (the radio that talks to your remotes), DigiKey or XP keypads (the wired or wireless entry pad), and the Photobeam or safety-loop inputs that feed back to the board. The compatibility gotcha with FAAC is the board generation. A 750 built before roughly 2012 uses a different input logic than a 750 built after, and plugging a new keypad into an old board without checking the revision can leave you with a gate that opens but never closes on its own. We always read the board silkscreen before ordering anything.
OEM versus aftermarket for FAAC is a real decision. OEM FAAC keypads and receivers run higher, but they carry a factory warranty and match the board inputs exactly. Quality aftermarket equivalents from brands like North Shore Commercial or Aleko can work fine on older FAAC models, but we’ve seen aftermarket receivers drift off frequency faster in Texas heat, particularly on west-facing Lewisville driveways that bake all afternoon. When the part is still available from FAAC, we lean OEM. When it’s discontinued, we’ll tell you that too and bring an equivalent that matches the input specs.
Signs Your FAAC Access Control Installation Is Failing
- Keypad lights up but the gate doesn’t move. The keypad is sending a signal, but the board isn’t receiving it. Usually a wiring fault at the terminal block or a dead relay channel on the keypad itself. We test continuity at the board, not at the keypad, because that’s where the failure actually lives.
- Remotes work only from ten feet or less. The RP receiver’s antenna wire is degraded or the receiver module itself is drifting. FAAC receivers are sensitive to antenna placement; if the antenna got pinched during a previous repair or the receiver sits too close to the motor capacitor, range drops off sharply.
- Gate opens for every code, including ones you never programmed. This is a receiver issue, not a keypad issue. The RP receiver has failed into an open state or a neighbor’s remote is on a matching dip-switch code. We’ve seen this exact problem in Highland Village and Castle Hills, and the fix is usually a receiver replacement with rolling code.
- Keypad is completely dead after rain. FAAC keypads are weather-rated but not waterproof, and Lewisville downpours find every seam. Water intrusion corrodes the ribbon connector inside. If the keypad has visible condensation behind the lens, it’s done.
- Gate works from the house button but not from the street. This isolates the problem to the street-side access device. If it’s a keypad, the issue is usually the keypad’s output transistor. If it’s a card reader, the reader’s Wiegand output has failed. Either way, the motor and board are fine.
BeforeAfterReplacement Cost & What’s Included
Here’s the pricing picture for Lewisville, written the way we quote it:
| Service | Installed Price Range | Typical Time |
|---|---|---|
| FAAC RP receiver replacement | $450 - $650 | 1-2 hours |
| FAAC DigiKey keypad replacement | $500 - $750 | 1-2 hours |
| Card reader plus controller retrofit | $800 - $1,200 | 2-4 hours |
| Full keypad + receiver + antenna package | $900 - $1,400 | 3-5 hours |
What drives the range is the part itself: OEM FAAC parts run higher than aftermarket, and a board revision that requires a converter adds labor. Every quote is written and handed to you before any work starts. You’ll see the part number, the labor, and the total. No line item appears after the fact. Under our 365-Day Done Right Promise, if the access control install fails within a year, we make it right at no charge. Every visit includes a photo log of what was found, what was set, and what was installed, left with you and filed in our job record.
DIY or Call Us?
What you can safely check: whether the keypad has power at all, whether the breaker feeding the gate operator is tripped, and whether any wires at the keypad or receiver are visibly disconnected. That’s real diagnostic information, and it helps us on the phone. What you should not do: open the operator cabinet and start probing terminals with a multimeter if you’re not comfortable around live 24VAC and 120V circuits. FAAC boards are not forgiving of a crossed wire or a slipped probe. We’ve repaired more than one board that a well-intentioned homeowner shorted while trying to test a keypad input. The board replacement costs more than the service call would have. If you’re unsure, call us at (817) 826-9477 and describe what you’re seeing. We’ll tell you over the phone whether it sounds like a quick check or a real repair, and what it’s likely to cost.
FAQs
Expect five to eight years from an OEM FAAC keypad or receiver in Lewisville’s climate, and closer to three to five from an aftermarket equivalent. The heat is the killer: direct afternoon sun on a west-facing keypad degrades the membrane and shortens the board’s life, and receivers mounted inside hot metal cabinets drift off frequency faster. We’ve replaced FAAC receivers that were fine electrically but simply couldn’t hold a signal after seven summers. Call (817) 826-9477 and we can read your part’s date code to estimate what’s left in it.
Sometimes, but not often. If the failure is a corroded ribbon connector or a broken wire at the terminal block, that’s repairable. If the board itself is fried or water has reached the keypad’s chip, the repair cost approaches replacement and we’ll tell you that before you spend anything. We never rebuild a keypad that we wouldn’t trust on our own gate. Call us with the symptom and we’ll give you an honest read.
Most FAAC keypad or receiver installations take one to two hours on site, and we typically complete them same-day when the part is in the truck. A full retrofit with a card reader and controller can run three to five hours depending on how much of the existing wiring is reusable. We’ll give you a written time estimate with your written price before any work starts.
We stock FAAC RP receivers, DigiKey keypads, antenna kits, and the common board input components on our trucks, so most Lewisville jobs don’t wait on a parts order. When your board revision requires a less common part, we order it and schedule the install the day it arrives. We also carry parts for LiftMaster, Mighty Mule, and Ghost Controls operators, so we can work on whatever motor is already on your property.
Written by Adrian Vance, Owner, Vance Gate Repair Lewisville at Vance Gate Repair Lewisville, serving Lewisville and nearby areas.