FAAC Gate Installation Nationwide

FAAC Gate Installation in Lewisville: What to Know First

FAAC gate installation in Lewisville runs $1,200-$4,800 for most residential jobs, depending on gate type, operator model, and site conditions. We’re an independent FAAC service provider, not an authorized dealer, and we install, replace, and repair the full range: swing gates, sliding gates, pedestrian gates, and double driveway gates. You get a written price before we touch anything, and most installations are scheduled within 5-10 business days. Call (817) 826-9477 for a free measure and written quote.

Call (817) 826-9477

This page is for Lewisville homeowners who already own a FAAC gate or operator, or are shopping for one, and want straight answers about cost, parts, and what actually goes wrong with these systems in North Texas. Adrian Vance founded this company out of commercial access-control work in 2014, and we’ve been documenting FAAC jobs the same way ever since.

Key Takeaways:

• FAAC systems are well-engineered, but their weaknesses show up in Texas heat and on long Lewisville driveway runs
• We service FAAC alongside LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so we’re never pushing you toward a brand you don’t need
• Every FAAC installation includes a written scope, a written price, and a photo record of what we did
• 365-Day Done Right Promise covers all completed work

How FAAC Products Fail - and How We Fix Them

FAAC builds solid operators. But every brand has its failure patterns, and we’ve seen enough FAAC units on Lewisville driveways to know exactly where they break and what to do about it. Here are the failure modes we run into most:

• Capacitor failure on the 400 and 402 series. The 400-series operators use a start capacitor that does not like sustained North Texas heat. We routinely replace capacitors on FAAC units that are five to seven years old. The symptom is usually a gate that hums but won’t move, or starts fine in the morning and stalls by afternoon. We replace the capacitor and photograph the new part with its date code. The part is under $40; the labor is the bulk of the repair.
• Limit-switch drift on the FAAC S418 and 750 series. The S418 (sliding gate) and 750 (swing gate) operators rely on mechanical limit switches that can drift after thousand of cycles. A gate that stops six inches short of full close is almost always a limit switch that needs resetting, not a new motor. We reset it, photograph the new setting, and note the reading in your job record so the next technician isn’t guessing.
• Photocell misalignment on gates with high foot traffic. FAAC’s safety photo-eyes, the infrared beams that stop the gate if anything crosses the path, get knocked out of alignment by gate vibration and careless mowing crews. A beam off by an inch or two makes the gate refuse to close or reverse unpredictably. We realign, verify with a test object, and photo-document the final beam position.
• Pump and hydraulic fluid leaks on the FAAC 770 underground swing gate system. The 770 hides the operator below grade, which is elegant, but the hydraulic seals degrade faster in clay-heavy Lewisville soil that holds moisture against the housing. You’ll see oil staining near the hinge post or a gate that moves noticeably slower. We replace seals, refill with the correct fluid, and check the line pressure.
• Control board damage from power surges. FAAC control boards are more sensitive to voltage spikes than some brands we work on, like LiftMaster. After a lightning-adjacent storm, we see dead display screens but intact motors. We test the board, replace it when necessary with a genuine FAAC or quality aftermarket board, and recommend a surge protector on the operator circuit if the panel doesn’t have one.

A note on parts: we use genuine FAAC parts for warranty-sensitive repairs when they’re available within a reasonable window. For older models where FAAC no longer stocks the part, or where an aftermarket component matches or exceeds the original spec, we tell you the difference, the price difference, and let you decide. That decision is documented in writing before the work starts.

Our FAAC Gate Installation Process

What follows is the same sequence on every FAAC installation we do in Lewisville, from a single pedestrian gate to a full double-swing driveway with operators on both leaves:

1. 1
   Free site measure and written scope. We come out, measure the gate, check the existing operator if one is present, and write down exactly what we’re doing, what parts we’re ordering, and what it costs. You get a copy before we schedule the install.
2. 2
   Parts ordering and confirmation. We order the FAAC operator and hardware, confirm delivery dates, and set your install date. If any part is backordered, we tell you before we accept the job, not after we’ve dug up your driveway.
3. 3
   Mounting and mechanical setup. We mount the operator, set the hinge and bracket geometry, and align everything before we touch any wiring. On swing gates, this is where we correct any existing sag or hinge wear so the new operator isn’t fighting a gate that was never hung straight.
4. 4
   Wiring, limits, and safety systems. We wire the operator to code, set the limit switches precisely, and install or verify the photo-eyes and safety edges. Every connection is photographed, and the wiring diagram is included in your job record.
5. 5
   Cycle testing and load check. We run the gate through a minimum of fifteen full open-close cycles, test the obstacle detection, and confirm the gate holds position without creeping. We’ll show you the test results and the photo log before we leave.
6. 6
   Documentation and walkthrough. You get the written scope, the photo record, any wiring diagrams, and the part numbers installed. Under Haven Standard Clause 4, evidence on every job, this documentation is included at no charge on every visit.

Before

After

What FAAC Gate Installation Costs in Lewisville

Most FAAC installations we quote in Lewisville fall into these ranges, and the written quote you get is the price you pay. No surprises at the end.

• Single swing gate, FAAC 391 or 400-series operator: $1,200-$2,400
• Double swing gate, two FAAC operators with master/slave control: $2,800-$4,800
• Sliding gate, FAAC S418 or 740 series: $1,800-$3,600
• Pedestrian gate with FAAC 390 or 770 underground operator: $1,400-$2,600
• Operator replacement on an existing gate (FAAC unit, reuse of existing brackets where sound): $850-$1,900

What moves the price: gate weight, the condition of the existing hinge hardware, whether we’re running new power to the gate, and whether safety edges need to be added to bring an older installation up to current standards. We’ll show you the line items. Call (817) 826-9477 for a free measure and written estimate.

Why Lewisville Homeowners Call Vance Gate Repair Lewisville for FAAC Work

Name what you found, name what it costs, name what you left behind. That’s the whole job. We started out in commercial access control, where a gate that doesn’t open doesn’t just annoy someone, it stops a truck from making a delivery. That kind of work doesn’t tolerate vague diagnoses, and we never picked up the habit of vague pricing. Adrian Vance brought that documentation habit to Lewisville residential gates, and it’s still how we work: written scope, written price, photo record on every visit.

We’re not a FAAC-only shop. We service nine gate automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing. If your Lewisville property has a FAAC on one gate and a Ghost Controls on another, we can handle both. If your FAAC operator is genuinely beyond repair and a different brand fits better, we’ll tell you that too. Our 365-Day Done Right Promise covers all completed work for a full year, and you’ll get a live person on the phone at (817) 826-9477 any hour of any day.

FAQs